ASTM A682 PDF

ASTM A682 PDF

admin

September 26, 2020

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Taurn Yozshurn
Country: Brazil
Language: English (Spanish)
Genre: Career
Published (Last): 4 November 2013
Pages: 145
PDF File Size: 13.93 Mb
ePub File Size: 19.75 Mb
ISBN: 625-2-44575-677-9
Downloads: 29746
Price: Free* [*Free Regsitration Required]
Uploader: Jull

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Over 12 Width Tolerance, Plus and Minus, in.

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

Materials and Manufacture 5. NOTE 2—Camber tolerances as shown in the table are for any mm length. Within the text, the SI units are shown in brackets. This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0.

For strip length under 8 ft.

ASTM A, AM_百度文库

This standard has been approved for use by agencies of the Department of Defense. Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production. C Number q682 edge strip with thickness tolerance guaranteed at less than 3? Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi?

  ELYONOVA ZEM PDF

Rework and Retreatment However, under SI the preferred term in mass. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges. Strip is classified as product that is 0.

Rejection and Rehearing Dimensions, Mass, and Permissible Variations 9. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

When the maximum manganese limit exceeds 1. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

In case of dissatisfaction with the results asm the test, the manufacturer may make claims for a rehearing. Two additional samples are secured from each end of the coil from which the original sample was taken.

General Requirements for Delivery 4. However, under SI the preferred term in mass. Normal coiling or piling does not provide a 3 Where an ellipsis. Table 3 shows requirements for additional asmt. When the amount of copper, nickel, chromium, or molybdenum is less than 0. This x682 produced when the edge condition is not a critical requirement for the? Link to Active This link will always route to the current Active version of the standard.

ASTM A682 Grade 1074

Link to Active This link will always route to the current Active version of the standard. For strip length under mm, camber tolerance shall be subject to negotiation.

Sstm, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Originally published as A — The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

  EDWARD UNCONDITIONALLY LYNN LORENZ PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. NOTE 2—Camber tolerances as shown in the table are for any 8 ft.

The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci? Current edition approved March 10, C When the chromium is speci? Combining values from the two systems will result in nonconformance with the specification.

The material must be ast protected and correctly identi? Within the text, the SI units are shown in brackets. Strip tolerance products may be available in widths wider than ?

Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size.

Note 1—The term weight is used when inch-pound units are the standard. The elements comprising the desired chemical composition are speci? NOTE 1—The term weight is used when inch-pound units are the wstm.