ELIWELL ID970 PDF

ELIWELL ID970 PDF

admin

November 9, 2020

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Gardalabar Mazurn
Country: Paraguay
Language: English (Spanish)
Genre: Science
Published (Last): 15 March 2009
Pages: 494
PDF File Size: 5.64 Mb
ePub File Size: 9.81 Mb
ISBN: 705-5-32096-790-1
Downloads: 53495
Price: Free* [*Free Regsitration Required]
Uploader: Shakalrajas

At the di970 of the lamp test, the following messages are displayed for about 5 seconds: ID LX Single stage controller for temperature. The parameter indicates that the protection is active on compressor relay actuations.

Eliwell reserves the right to make any changes or improvements without prior notice and at any time. Single stage controller for temperature. In addition, the 16 A compressor relay options and the buzzer are provided. The operation cannot be cancelled. This means, for example, that an error introduced by the probe is added to any error that is typical of the instrument. Defrost counting is always active when the machine is on and starts at each power-on.

Do not assemble the instrument in excessively humid or dirty locations since it is designed to be used in locations with normal pollution levels. For this page to function properly, you must enable JavaScript.

Defrost cycles can be controlled at time intervals. Description Technical Schema Description: Set point setting folder; -Pb1: Always make sure that the area next to the cooling openings of the tool idd970 adequately ventilated. Eilwell the request and effective activation of the compressor relay, at least the specified time must elapse.

  ALBIN LESKY PDF

All the versions are provided with a TTL connection in order to use Copy Card, the quick programming accessory. HSE maximum set cannot be less than LSE minimum set and vice versa Compressor activation time in the event of a faulty probe. They are provided with a Elowell thermostatic probe input NTC can be selected by parameter and two relay outputs for compressor and defrost management.

Single stage controller for temperature ID Single stage controller for temperature – ID The ID controllers are devices suitable for applications on normal or low temperature refrigerating units.

If one or more ic970 are modified, it is suggested to the switch off the controller after the modification and then switched back on. ID Single stage controller for eliwel. Positive or negative temperature value added to the value read by probe Viewing mode during defrosting. It’s a community-based project which helps to repair anything. Delay time in activating the outputs after switch-on of the instrument or after a power failure.

The two sets are interdependent: Delay after switching off. ID A Single stage controller for temperature. The programming parameters are downloaded when the device is switched on.

TTL for connection to Copy Card 3 eiwell on relays: JavaScript is disabled in your browser. The Setpoint value appears on the display. Compressor off time in the event of a faulty probe.

It is classified as follows: The indicated time must elapse between two subsequent switch-ons of the compressor.

  DRUNVALO MELCHIZEDEK MERKABA PDF

Eliwell ID MC (Milk) |

Probe cables, power supply cables and the TTL serial cable should be kept separate from power cables. Temperature value understood as distance from the Setpoint or as an absolute value based eliaell Att which if exceeded in a downward direction triggers the activation of the alarm signal. Alarm exclusion time after instrument is switched on following a power failure.

The relay contacts are voltage-free. For higher loads, use a suitable contactor.

Eliwell ID970 MC (Milk)

The sensor has no connection polarity and can be extended using an ordinary bipolar cable note that extending the probe may affect the electromagnetic compatibility EMC of the instrument: Make sure that the power voltage complies with the device voltage. Do not exceed the maximum eiwell allowed. Drill a 29×71 mm hole, insert a tool and fix it in place with the brackets provided.

Download from reset Connect the copy card when the instrument is OFF. The Setpoint can also be viewed. eliwel

Minimum possible setpoint value. Every time the compressor stops, a defrosting cycle is performed according to parameter dty dOH Defrost start delay time from start up of instrument.

It should be noted that the relay contacts supplied with the device are functional and therefore exposed to potential faults. The continuous improvement of our products can eliewll some variations in this non contractual document even without notice.