October 1, 2020

Guard Ring Die Construction for Transient Protection. •. Low Power Loss, High Efficiency. •. High Surge Capability. •. High Current Capability and Low Forward. IN datasheet, IN circuit, IN data sheet: FCI – Amp BARRIER SCHOTTKY RECTIFIERS,alldatasheet, datasheet, Datasheet search site for. IN datasheet, IN circuit, IN data sheet: CHENG-YI – MINIATURE SCHOTTKY BARRIER RECTIFIER,alldatasheet, datasheet, Datasheet search.

Author: Grolabar Nikorr
Country: Romania
Language: English (Spanish)
Genre: Life
Published (Last): 3 March 2017
Pages: 139
PDF File Size: 16.9 Mb
ePub File Size: 19.9 Mb
ISBN: 269-2-14155-872-6
Downloads: 29604
Price: Free* [*Free Regsitration Required]
Uploader: Voodookazahn

For best results, external components should be located as close to the switcher IC as possible using ground plane construction or single point grounding. These temperature rise numbers are all approximate and there are many factors that can affect these temperatures. If open core inductors are used, special care must be taken as to the location and positioning of this type of inductor.

Physically locate both resistors near the IC, and route the wiring away form the inductor especially an open core type of inductor. Feedback Senses the regulated output voltage to complete the feedback loop.

For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should be used in the board layout. The TO surface mount package tab is designed to be soldered to the copper on a printed circuit board.

Large areas of copper provide the best transfer of heat lower thermal resistance to the surrounding air, and moving air lowers the thermal resistance even further. Typical Performance Characteristics Figure 4. Additional copper area improves the thermal characteristicsbut with copper areas greater than approximately 6 in 2only small improvements in heat dissipation are realized.

This data was taken with the circuit operating as a buck switching regulator with all components mounted on a PC board to simulate the junction temperature under actual operating conditions. Quiescent Current vs Temperature Figure 9. Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these spikes.


Symbol Parameter Conditions Min. When using the adjustable version, special care must be taken as to the location of the feedback resistors and the associated wiring.

The TD TO package junction temperature rise above ambient temperature with a 3A load for various input and output voltages.

The TD junction temperature rises above ambient temperature for a 3A load and different input and output voltages. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be kept a minimum. The copper and the board are the heat sink for this package and the other heat producing components, such as the catch diode and inductor.

It is capable of driving a 3A load with excellent line and load regulation. The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor.

Output Saturation Characteristics Figure 7.

IN datasheet & applicatoin notes – Datasheet Archive

The voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance in58211 the output filter capacitor, To minimize these voltage spikes, special low inductance capacitors can be used, and their lead lengths must be kept short.

Exposure to absolute maximum rating conditions for extended periods may affect reliability. An additional small LC filter can be added to the output as shown in Figure 14 to further reduce the amount of output ripple and transients.


Once exception to this is the output switch pin, which should not have ln5821 areas of copper. The PC board copper area that the package is soldered to should be at least 0.

(PDF) IN5821 Datasheet download

The device is available in an adjustable or fixed output version. Stresses greater than those listed under Maximum Ratings may cause permanent damage to the device. The size of the heatsink depends on the input voltage, the output voltage, the load current and the ambient temperature.

This curve can be used for a quick check for the approximate junction temperature for various conditions, but be aware that there are many factors that can affect the junction temperature. A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by the regulator.


As in any switching dstasheet, layout is very important. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied. Pulling this pin below a threshold voltage of approximately dtaasheet. Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation, and a fixed-frequency oscillator.

Rapidly switching currents associated with wiring inductance can generate voltage transients which can cause problems.

Self protection features include a two stage frequency reducing current limit for the output switch and an over temperature shutdown for complete protection under fault conditions. Higher ambient temperatures require more heat sinking.