IPMP CONFIGURATION SOLARIS 10 PDF

IPMP CONFIGURATION SOLARIS 10 PDF

admin

September 20, 2021

Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the. You must have configured all interfaces as members of the IPMP group. role to a user, see Chapter 2, Working With the Solaris Management Console (Tasks).

Author: Taull Faujinn
Country: New Zealand
Language: English (Spanish)
Genre: Life
Published (Last): 10 September 2010
Pages: 353
PDF File Size: 20.16 Mb
ePub File Size: 15.70 Mb
ISBN: 865-1-42988-954-3
Downloads: 7323
Price: Free* [*Free Regsitration Required]
Uploader: Braktilar

Repair detection assumes that you have enabled failbacks. Devices and File Systems. If you need additional data IP addresses you should add them as deprecated IP interfaces. Similarly, if you configure as standby an interface that already has data addresses, these addresses automatically fail configruation to another interface in the IPMP group. Created new logical interface hme0: For an interface to use probe-based failure and repair detection, that interface must be confjguration with at least one test address.

When an interface is considered repaired, any addresses that failed over to another interface then fail back to the repaired interface. Configure an interface as a standby and assign the test address. For example, to configure hme0 with an IPv6 test address, you would type the following: The standby interface in an IPMP group is not used for data traffic unless some other interface in the group fails.

  BOBRICK B-2892 PDF

You should receive a status message regarding this event. If one interface in the group is to become the standby interface, do not configure a test address for that interface at this time.

IP Security Architecture Reference. IPv6 in Depth Reference.

How to configure Solaris 10 Probe based IPMP

However, if all of the probe targets on bge0 become unreachable, only bge0 will be reported as failed because bge has its own probe targets on its own VLAN. Leave a Reply Cancel reply Your email address will not be published.

An active interface is a physical interface that configuraion both data traffic and probe traffic.

This process is called load spreading. Puppet Automation – Live WebEx. These interfaces and the data addresses that are configured on them are immediately available for use by the IPMP group. A single interface can be configured in its own IPMP group.

IPMP Configuration – Solaris 10 vs Solaris 11

Its really awesome article. Some Sun platforms might only support DR of certain types of hardware.

A group failure occurs when all interfaces in an IPMP group appear to fail at the configiration time. Depending on your failure detection requirements, you might need to either use specific types of network interfaces or configure additional IP addresses on each network interface.

  CCNL GOMMA PLASTICA INDUSTRIA 2011 PDF

These physical interfaces might or might not be on the same NIC. Some failovers might not choose a standby interface. For example, to create an IPv6 test address, you would type the following command: Configuratio NCP to be enabled:.

How to configure Solaris 10 Probe based IPMP – The Geek Diary

If the system has additional interfaces on a second IP link, you must configure these interfaces as another IPMP group. Currently you have JavaScript disabled. The probing rate depends on the failure detection time FDT. You need to configure a test address only if you want to use probe-based failure detection on a configurqtion interface.

IPMP Interface Configurations – Oracle Solaris Administration: IP Services

For more information on link-local addresses, refer to Link-Local Unicast Address. Enable Probe-Based Failure Detection. You would type the following command: You can always view the current status of an interface by ippmp ifconfig interface. Some failovers might not choose a standby interface. In this instance, the test IPv4 address is configured only on the next reboot. Solaris11 Self Paced Video Learning.