ISO 10555-5 PDF

ISO 10555-5 PDF


October 30, 2020

The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to. à aiguille interne. STANDARD. ISO. Second edition. Reference number. ISO (E). Provläsningsexemplar / Preview. STANDARD. ISO. Second edition. Reference number. ISO (E). This is a free 4 page sample. Access the full version online.

Author: Taugar Kikazahn
Country: Angola
Language: English (Spanish)
Genre: Art
Published (Last): 27 February 2005
Pages: 73
PDF File Size: 16.87 Mb
ePub File Size: 3.41 Mb
ISBN: 458-1-46483-431-1
Downloads: 84450
Price: Free* [*Free Regsitration Required]
Uploader: Faekree

Page 3, subclause 4. Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Add the following reference: This 105555-5 Standard has been developed from Doc No.: The fluid is allowed to flow into the needle, and the time taken for fluid to leak through the vent fitting is measured.

Catheter designed for the introduction or withdrawal of liquids or devices into or from the peripheral vascular system. Rigid tube with one end sharpened to facilitate entry into body tissue. Designation and catalogue of CCR colours. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated expressing the result of a 15055-5 or analysis, shall be rounded off in accordance with IS 2: No part of the these publications may be reproduced in any form without the prior permission in writing of BIS.

Peripheral intravascular catheter designed for the introduction of withdrawal of liquids or devices into or from the peripheral vascular system.

BS EN ISO 10555-5:2013

The assembly comprising at least a needle tube attached to and communicating with a needle hub. Assembly comprising the cath- eter tube, catheter hub and any integral fittings. Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country.


Part 1 General requirements do The technical committee has reviewed the provisions of the following International Standard referred in this adopted standard and has decided that it is acceptable for use in conjunction with this standard: The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. The details of conditions under which the licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards.

Assembly comprising at least a needle tube attached to, and communicating with, a needle hub. At the time of publication, the editions indicated were valid. Search the history of over billion web pages on the Internet.

Until that time, a manufacturer may label his product “radio- opaque” provided he can support this claim by demonstrat- ing that he has an appropriate method for showing radio- opacity. In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist.

Annex D shows examples of typical needle point geom- etries. The catheter tube may have a single lumen or multiple lumens. Fitting attached to the needle tube, providing communication with its bore. I Principle Water is allowed to flow through the catheter and the amount of flow is measured either volumetrically or gravimetrically.

Measure the time taken for fluid to form the first falling drop io the back of the vent fitting. Fixed or removable fitting per- mitting venting of air while restricting or preferably preventing the escape of blood.

I Principle A force is applied successively tensile and connpress- ive to the needle tube and needle hub and the tube- hub union is then examined for loosening. NOTE 3 The point should be designed to be noncoring.


Intravascular catheters ISO , -3, -4, -5

The corresponding Indian Standards which are to be substituted in their places are listed below along with their degree of equivalence for the editions indicated: E-5 Test report The test report shall contain at least the following information: Available from Munsell Color, N. All 110555-5 are subject to revision, and parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.

International Standard ISO An example of a suitable apparatus is shown in fig- ure B. Details of which is given in National Annex A. An approved test method for 10555–5 a value of radio-detectability will be established. When tested in accordance with annex E, fluid shall not leak out of the vent fitting within 15 s. Copyright BIS has the copyright of all its publications. When the needle is fully inserted into the catheter unit, the catheter tube shall neither extend beyond the heel of the needle bevel nor be nnore than 1055-55 nnnn fronn it see dinnension a in 10555- 1.

Round the calculated average water fiowrate to the nearest whole number of millilitres. Certain conventions are, however, not identical to those used in Indian Standards.

Suggested colour references for opaque naaterials are given in annex C. The fluid pathway in the needle shall be free of unintended obstructions that would prevent flashback.

Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: