Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une éprouvette rotative. STANDARD. ISO. Second edition. ISO – Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen. ISO Paints and varnishes – Determination of resistance to abrasion – Part 2: Method with abrasive rubber wheels and rotating test specimen.
|Published (Last):||20 March 2008|
|PDF File Size:||16.72 Mb|
|ePub File Size:||4.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
Teknos to acquire powder coatings business from Sniezka 19th January Read more. Application Properties and Appearance: This guide is intended to assist in establishing procedures for determining the relative resistance of treated or untreated mortar surfaces.
BS E17 and ISO are alternative names for the same method which is used to assess the resistance of a dry film of paint, varnish or related product to marring by a looped or a ring-shaped stylus. We will be pleased to advise you regarding our requirements. This specification describes the required properties and test methods for a cold liquid-applied elastomeric izo for waterproofing building decks not subject to hydrostatic pressure.
This test measures the ability of the decorative surface of melamine surfaces boards to resist abrasive wear-through by rotating a specimen in contact with cylindrical wheels covered with abrasive paper. Sample Requirements We require ml of sample together with information regarding the film thickness at which the coating should be applied.
This procedure covers the determination of the resistance of coatings to abrasion using the Taber Abraser. This specification establishes the requirements for high-durability, wear-resistant deck coatings for use in high-traffic areas, with minimal maintenance.
New AkzoNobel site strengthens leading powder coatings position in China 25th January Read more. BS E14, ISO Scope and Isoo Application BS E14 and ISO are alternative names for the same method which is intended for determining the resistance to abrasion of a dry film of paint, varnish or related product using abrasive paper attached to a rotating wheel.
Taber Test Methods: Taber Abraser (Abrader) – Taber Industries
This specification does not address, and therefore is not applicable to, ground-face concrete masonry units that are manufactured by grinding a 7784- layer off the surface of a concrete masonry unit to 784-2 aggregates within and kso to produce smooth, architectural finish.
The resistance to abrasive damage is judged qualitatively by its effect on the legibility, pattern, and color of the graphic marking. ASTM C Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and inert filler, or cement and inert filler to produce a smooth resinous tile facing.
If we are to determine the largest mandrel that causes failure, we need 15 panels for each coating. Detached paint flakes should be at least as large as your thumb nail and should include all layers from the one adjacent to the substrate up to the top coat.
This specification covers iiso material performance and laboratory test procedures for non-reinforced liquid coating encapsulation products single or multiple-coat systems for leaded paint in buildings.
Tape shall consist of glass spheres of a high optical quality imbedded into isk binder on a suitable backing that is pre-coated with a pressure-sensitive adhesive. Follow these links to find other Standards similar to the one you are viewing. This specification describes the general requirements for test equipment used in testing electrical and electronic equipment.
This Specification provides the requirements and procedures for isoo a hard oxide coating on aluminum alloys. Determination of Surface Drying Time: In some cases the test method will be specified but in others it is necessary to choose the most appropriate method.
Sample Requirements The test piece can be as small as 10 x 10 on any smooth rigid substrate.
We need 3 coated panels for each coating. This standard covers the test method for polyurethane PU of athletic installation use.
BS EN ISO 7784-2:2016
This guide covers the selection and use of procedures for testing traffic paints in the laboratory and in the field. Chemture shareholders approve acquisition by Lanxess 8th February 7784-22 more.
This Japanese Industrial Standard applies to building materials and parts of building construction and specifies the testing method to evaluate the degree of abrasion of the test piece. We can cut larger panels to size for you or, if you wish, we can prepare the test panels. Steel or aluminium are the preferred substrates although we have used this test on coatings applied to rigid plastics.
This standard sets out a method for the determination of the abrasion resistance of textile fabrics applicable to all textile fabrics including coated and laminated fabrics, a method for wet testing is also specified.
It shall be used when specified on the Engineering drawing. Sample Requirements Three panels x x not greater than 1 mm. Three test panels of dimensions x x not greater than 1 mm. Sample Requirements Detached paint flakes should be at least as large as your thumb nail and 7748-2 include all layers from the one adjacent to the substrate up to the top coat.
BS AU Part