LM2940CT-5.0 DATASHEET PDF

LM2940CT-5.0 DATASHEET PDF

admin

October 8, 2020

LMCT-5 Datasheet, LM 5V Low Dropout Voltage Regulator Datasheet, buy LMCT Pin 5 and 6 need to be tied together on PCB board (5) ESD rating is based on the human body model, pF discharged LMCT/NOPB .. in TI data books or data sheets is permissible only if reproduction is without alteration. Digi-Key Part Number, LMCT/NOPB-ND. Copy LMCT/NOPB- ND. Quantity Datasheets, LMN, C Datasheet. Design Resources.

Author: Monos Akit
Country: Barbados
Language: English (Spanish)
Genre: Literature
Published (Last): 22 November 2014
Pages: 383
PDF File Size: 8.59 Mb
ePub File Size: 3.10 Mb
ISBN: 541-7-56123-461-9
Downloads: 15233
Price: Free* [*Free Regsitration Required]
Uploader: JoJozilkree

LDO Voltage Regulator (5V 1A LMCT, drop V @A) in Canada Robotix

I will try it with the additional cap. Even linear regulators are switching dataheet, which generate some noise that must be filtered. Larger values of output capacitance will give improved transient response.

There is lm2940ctt-5.0 possibility Many of the regulators require capacitance on the input and output to minimize oscillation. According to the diagram Input is on the left, GND is in the middle, and the 5V output should be on the right. If you look at the diagram on the first page you will see some asterisks next to the capacitors. Does it have a backlight?

I like to put a led on the output for the minimum load, and to show, solidly, that power IS really on. Osgeld Faraday Member Posts: The circuit I’m building works fine with a 5V regulated supply one you plug into the wallbut Datqsheet like to expand the design to work off of batteries as well.

  CONCERTO FOR MARIMBA AND STRINGS EMMANUEL SEJOURNE PDF

LMCT/NOPB Datasheet(PDF) – TI store

The only things being powered in the circuit is the stamp and the LCD. Also, remember the more voltage you have to drop and the more current you want to pull, the hotter the device will run.

If you aren’t running very much current, and your Vin isn’t too high, a small clip-on heat sink can significantly reduce the regulator’s temperature. Otherwise the output impedance datsaheet too high and it oscillates.

I’m pretty sure Cap value correlates to the noise frequency, so no, you can’t just “go over” the value and still have the same effect. The wiring diagrams in the datasheet include capacitors, but I assume that these are for smoothing out ripple, and would have no effect datzsheet this massive increase in voltage I’m seeing.

Here’s a snip from p. I wonder if anyone knows if the capacitors have any effect beyond smoothing out ripple. Is ths just because of the load placed on it due to the lcd? I haven’t experienced it personally, but you could have an issue there that might result in overheating. I picked up some 5V 1A voltage regulators at a shop in town. I have a 22uf cap between the output and ground as specified in the datasheet for stability. Click for larger version I found a datasheet here: Typically, LCD displays take very little, but I’m dtasheet familiar with the unit you’re using.

  LEI 10705 ITCMD SP PDF

I believe the data sheets show a 0. My input is 9V, I’m using the power supply that came with the P40 demo board. I went digging through my dad’s old junk box and found a 16V, uF electrolytic cap. It’s interesting that mine gets this hot when I have seen schematics using the same setup, with a 10uf cap even.

Comments 10 Comments sorted by Date Added Votes.

LDO Voltage Regulator (5V 1A LM2940CT, drop 0.5V @0.5A)

OK – I see the third line info now! I can’t find a schematic of it. The cap values are related to the frequency of the noise to be filtered.

Should I use some other voltage regulator? The output capacitor is required to ‘maintain stability’ which probably means to keep it from oscillating, which in turn could cause the strange output readings you are getting.

The power in Watts being dissipated within the regulator is the voltage drop across the regulator times the current passing through it.